Mechanical Engineers

 
Home | Bearing design, manufacture an | Pump engineering | Piping & fluid mechanics engin | Optical systems engineering | Mechanical Seal engineering | Mechanical engineering other t | Mechanical Acoustics/Vibration | Laser engineering
  Position:Home>Pump engineering>Article Content
Test pump packing
Source:Internet Author:Unknow Pubdate:2010-06-29  
puckman31 (Electrical) 20 May 10 4:32
Is there a method to test a pump that uses packing for a seal when on the bench and no motor attahed? This is so the pump is not installed and then find out that it is leaking way to much when operated.

Artisi (Mechanical) 20 May 10 5:20
Leaking from where - the castings, the casing joint, the gland / stuffing box?  please explain.

   

puckman31 (Electrical) 20 May 10 5:33
I am looking for a test method for packing a pump that would indicate there is a problem before it is installed.
Thank you to all who respond.

micalbrch (Mechanical) 20 May 10 6:55
= test a pump without having the motor installed and find out whether there is leakage over the packing (shaft seal) or not.
字串5


JohnGP (Mechanical) 20 May 10 15:28
Sorry, have never seen the need for such a test. If a pump with new packing leaked "way too much" when run, then it would probably take less time to check why it was and then repack, if the installed packing could not be taken up a bit more.

Artisi (Mechanical) 20 May 10 18:24
There is no way to test the packing on the bench, the pump needs to be run and the packing bedded into the stuffing box over a period of run-time.  

puckman31 (Electrical) 23 May 10 7:52
thanks for all the responses and help

pumpking (Chemical) 27 May 10 18:23
There is very little to go wrong with packing - insufficient compression, over compressed packing or wrong size packing ?  Remember it must leak to work properly to lubricate... Ash Fenn 字串1

www.cdrpumps.co.uk

ABritTurner (Mechanical) 19 Jun 10 8:29
Remove current packing  and repack with proper packing leave gland out to full for further tightening under pressure. There is no need to test as long as you use the proper packing. Contact a packing manufacturer/supplier and read up on packing for oil/water/steam packing at pressures you need.   

(Click:
Previous:Centrifugal or Vertical Turbine?   Next:Looking for a Pump Curve
[Add TO Favorites] [TOP] [PRINT] [CLOCE WINDOWS]  
  Hot Article
·Heat Gain from Pump Motors
·Pump NPSH calculation spreadsh
·ANSI vs. API pump O&M
·KSB feed pump balancing disc d
·Calculating tip speed?
·pump and system curve
·Centrifugal Compressor Curves
·NPSH margin and ANSI/HI 9.6.1
·Liquid ring vacuum pump
·Pump power calculation
·Gerotor Pump Design software
·NPSHa Vertical Turbine Pumps
  Related Articles
·Looking for a Pump Curve
·Is sulfur erosive on a pump
·Electricity demand for the pum
·Pressure-Flow performance
·Pump affinity laws
·Metric to American conversion
·the way of control displacemen
·Preferable method to set in we
·"trash pump" manufac
·Packaged Booster Pump Selectio
·Positive Displacement Pumps in
·VFD or variable displacement?
MBT SHOES CLEARANCE SALE Cheap LouisVuitton Bags Civil / Environmental Engineers Structural Engineers Aeronautic Engineers Automotive Engineers Chemical Engineers Geotechnical Engineers Industrial / Manufacturing Engineers Materials Engineers Computer Engineers Agricultural Engineers Mechanical Engineers Petroleum Engineers Bioengineers Military Engineers